One sheet wonder - 12 x 12 DSP

 This is a one sheet wonder for 12 x 12 DSP which will make the 15 cards below.  It also works for 6 x 6 squares.  

Cut a 12 x 12 into 16 squares 3 x 3 inches.  (If using 6 inch squares you can cut into four 3 x 3 inch squares and make whichever cards you like.  One 6 inch square will make cards 1-3.  One 6 inch square can make any 4 of cards 4-15.)

For the first 3 cards you will cut one of the 3 inch squares into 1 inch strips (1 x 3 inches).  Each card uses 1 of the 3 inch squares and 1 of the 1 inch strips. 

Card 1 

 DSP 3 inch square; 1 x 3 inch strip

Black mats - 3 1/4 inch square; 1 1/4 x 3 1/4 inch strip

Card 2

DSP 3 inch square; 1 x 3 inch strip

Black mat - 3 1/4 x 4 1/2 inches

(Can be landscape or portrait)

Card 3

   

DSP 3 inch square; 1 x 3 inch strip

Black mats 3 1/4 inch square; 1 1/4 x 3 1/4 inch strip

(Can be landscape or portrait)

Cards 4-15 each use one of the 3 inch squares.  

Card 4

DSP 3 inch square

White mat 3 1/4 x 4 1/2 inches

Black mat 3 3/8 x 4 5/8

Card 5

DSP 3 inch square - Cut diagonally tip to tip

Black mat 3 1/4 x 4 3/8. Can be cut 4 1/2 also

Card 6

DSP 3 inch square cut on diagonal - not at the tips

Black mat - 3 1/4 x 3 3/4

Card 7

DSP 3 x 3 inch square, cut curvy line across the middle

Black mat 31/4 x 3 3/4

Card 8

DSP 3 x 3 inch square - tear about 1/3 from right edge.  Flip the piece and glue to the back.

(if your paper is not double sided - take a 3 inch square with a different design and tear in a similar manner.  Swap out the pieces.

Black mat - 3 1/4 x 4 1/2

Card 9 

DSP 3 inch square cut at 1 1/2 inch (two pieces 1 1/2 x 3)

Black mats - 1 3/4 x 3 1/4

Card 10 

DSP 3 inch square cut into 1 1/2 inch squares

Black mat 3 1/2 x 3 1/2

(one side was a little wider border of black so I trimmed off about 1/8 inch ??)

Card 11

DSP 3 inch square cut into three 1 inch strips

Black mat - 3 1/4 x 3 1/2

Card 12

DSP 3 inch square cut into three 1 inch strips

Black mat - 1 1/4 x 3 1/4

Card 13

DSP 3 inch square cut into 3/4 inch strips

Black mats 1 inch x 3 1/4 inch

(all 4 strips could be placed on one mat 3 1/4 x 3 5/8)

Card 14 

DSP 3 inch square cut at 3/4 inch, 1 inch, leaving a 1 1/4 inch strip.

Black mat - 3 5/8

Card 15 - 

DSP 3 inch square - cut into nine 1 inch squares

Black mats - nine 1 inch squares

Glue DSP onto the black leaving a 'shadow' on 2 adjacent sides.